Product introduction：
Junda JD400DA-28 gallon sandblasting pot, with built-in vacuum abrasive recovery system, which can use conventional abrasives such as garnet sand, brown corundum, glass beads, etc，and the built-in recovery vacuum motor and dust filter can recycle and improve the efficiency of using the abrasive。
Product feature：
1, movable sand storage tank, rear wheel is convenient for transportation.
2, built-in recovery vacuum motor and vacuum filter element
3, can recycle abrasive, reduce the cost of rust removal.
Product Application：
Quotation is mainly used for all kinds of steel plate rust removal, steel structure rust removal, ship refurbishment, automobile refurbishment, anti-corrosion engineering, oil pipeline anti-rust removal, shipyard rust removal, engineering vehicles
Refurbishment, mechanical equipment refurbishment, metal mold surface sandblasting.
Operation instructions and Precautions：
1. If the protected brush transmission device is not in the proper position, put it right immediately.
2. Set the air compressor to 8 kg force/square centimeter.
(More or less, depending on the surface to be treated)
3. Connect the air pipe connector to the air inlet connector located on the handle.
4. Connect the power cable to the power supply.
5. Aim the gun at the surface to be cleaned and turn the switch on the top of the vacuum machine to the open position.
6.Hold the gun in one hand and the brush handle in the other. Note: Do not apply pressure by pointing the brush at the treated surface! The function of the brush is only to prevent the waste of sand, and then for grinding
The material is kept in a sealed vacuum cycle to achieve recirculation. Brushes are not expected to play an auxiliary role in abrasion processing.
7. Both hands should move in the direction of the rust removal or pre-painted working surface.
8. You can vary the size of the jet by extending or shortening the nozzle with a lock nut.
9, hard brush can be used for plane, can also be used for angle, corner. Before you start, spread the bristles out so they don't cover the spray holes in the brush.
(Abrasives wear down the bristles)
On the edge of the car door, we suggest that you wrap stiff hair around the edge of the door for good vacuum environment and good coverage.
10. After each work, remove the vacuum brush and flick off the dust on the filter element. After one hour of continuous work, remove the vacuum brush and use DC air or vacuum cleaner
Blow off the dust.
11. When spraying at a 90 degree angle, adjust the gun at a 45 degree Angle to reach the deep position. Move the spray gun slowly in a circular motion to achieve the effect. After sandblasting, loosen the two clamps and empty
Dust collecting filter element and store abrasive in a dry way.
Junda JD400DA-28 gallon sandblasting pot, with built-in vacuum abrasive recovery system, which can use conventional abrasives such as garnet sand, brown corundum, glass beads, etc，and the built-in recovery vacuum motor and dust filter can recycle and improve the efficiency of using the abrasive。
Product feature：
1, movable sand storage tank, rear wheel is convenient for transportation.
2, built-in recovery vacuum motor and vacuum filter element
3, can recycle abrasive, reduce the cost of rust removal.
Product Application：
Quotation is mainly used for all kinds of steel plate rust removal, steel structure rust removal, ship refurbishment, automobile refurbishment, anti-corrosion engineering, oil pipeline anti-rust removal, shipyard rust removal, engineering vehicles
Refurbishment, mechanical equipment refurbishment, metal mold surface sandblasting.
Operation instructions and Precautions：
1. If the protected brush transmission device is not in the proper position, put it right immediately.
2. Set the air compressor to 8 kg force/square centimeter.
(More or less, depending on the surface to be treated)
3. Connect the air pipe connector to the air inlet connector located on the handle.
4. Connect the power cable to the power supply.
5. Aim the gun at the surface to be cleaned and turn the switch on the top of the vacuum machine to the open position.
6.Hold the gun in one hand and the brush handle in the other. Note: Do not apply pressure by pointing the brush at the treated surface! The function of the brush is only to prevent the waste of sand, and then for grinding
The material is kept in a sealed vacuum cycle to achieve recirculation. Brushes are not expected to play an auxiliary role in abrasion processing.
7. Both hands should move in the direction of the rust removal or pre-painted working surface.
8. You can vary the size of the jet by extending or shortening the nozzle with a lock nut.
9, hard brush can be used for plane, can also be used for angle, corner. Before you start, spread the bristles out so they don't cover the spray holes in the brush.
(Abrasives wear down the bristles)
On the edge of the car door, we suggest that you wrap stiff hair around the edge of the door for good vacuum environment and good coverage.
10. After each work, remove the vacuum brush and flick off the dust on the filter element. After one hour of continuous work, remove the vacuum brush and use DC air or vacuum cleaner
Blow off the dust.
11. When spraying at a 90 degree angle, adjust the gun at a 45 degree Angle to reach the deep position. Move the spray gun slowly in a circular motion to achieve the effect. After sandblasting, loosen the two clamps and empty
Dust collecting filter element and store abrasive in a dry way.
